Learn about your home's detectors

smoke and carbon monoxide detector information

Troubleshoot Your Detectors

Several things could be causing your alarm(s) to alarm briefly or Chirp randomly without a regular pattern.

Is it Consistently at regular time intervals?  If your alarm is chirping or sounding randomly, change the battery to see if it fixes the problem.

Or is it Randomly without a regular pattern?  Refer to the section below for possible causes and solutions to the problem.

Products Affected:

1.)  Kidde-manufactured smoke alarms
2.)  carbon monoxide alarms
3.)  combination alarms
4.)  heat alarms

Diagnose your detector's problem

Loose or Improperly Installed Battery

Refer to the following checklist and determine if one of these conditions might be the cause of your problem:

1.)  Verify that a battery of the recommended type is securely installed.

2.)  Make sure to use a battery with a use-by date no later than four to five years in the future.

3.)  Check that the battery is snapped in completely so it cannot be shaken loose.

NOTE: It is possible that battery connections may not be making good contact with the battery.  Disconnecting and re-connecting the battery once or twice will likely fix this condition.

NOTE: On units with a front-load battery, be sure that the battery compartment door is closed completely as well.

NOTE: Loose white neutral wire can cause an echoing chirp from one unit to the next.

Smoke Alarm Sensing Chamber May be Dirty

To clean your smoke alarm, perform the following steps:

1.)  Remove your alarm from the mounting bracket

2.)  Clean the interior of your alarm (sensing chamber) by using compressed air or a vacuum cleaner hose and blowing or vacuuming through the openings around the perimeter of the alarm.

3.)  Clean the outside of the alarm by wiping it down with a damp cloth.

4.)  After cleaning, reinstall your alarm, verify the green LED is on and test your alarm by using the Test button.

NOTE: Dust and insects can collect in the sensing chamber of the alarm.  An accumulation of dust in the sensing chamber can cause the unit to chirp.  It is good practice to clean the smoke alarm when you change the battery.  Static electricity from the ac quick connector attracts dust and can cause false alarms.

NOTE: If cleaning does not restore the alarm to normal operation, the alarm should be replaced.

Environmental Conditions

Refer to the following environmental conditions for possible solutions to an alarm’s random chirping:

1.)  Humidity, steam and condensation

2.)  Extreme temperatures changes.  Check the temperature of the room. Smoke alarms operate at 40 degrees to 95 degrees Fahrenheit.  Carbon monoxide alarms operate at 40 degrees to 100 degrees Fahrenheit.

3.)  High ambient humidity.

4.)  Unit being installed in an uninsulated electrical box mounted on a ceiling beneath an attic.

NOTE: If this condition exists you will want to move the alarm.  View the correct alarm placement in your user’s manual.

Excess airflow:

Check to see if there is a cooling/heating register, a ceiling fan or an open window within 3 feet of the alarm.  If there is, move the alarm away from the source of the increased airflow.

NOTE:  View the correct alarm placement in your user’s manual.

Resetting the Alarm

To reset an AC unit with a battery backup:

1.)  Turn off the power to the smoke alarm at the circuit breaker.

2.)  Remove the smoke alarm from the mounting bracket and disconnect the power.

3.)  Remove the battery.

4.)  Press and hold the test button for at least 15 seconds.

5.)  Reconnect the power and reinstall the battery.

Resetting a DC only unit:

1.)  Remove the battery.

2.)  Press and hold the test button for at least 15 seconds.

3.)  Reinstall the battery.

NOTE: The unit may chirp or alarm for a few seconds before going silent.

NOTE: Some current model smoke alarms have a processor that retains certain error conditions which must be manually reset to clear the error.

Electrical Condition

If the AC power to the unit is interrupted, the unit will chirp when the power is restored. This could be caused by power surges.

1.)  If the chirping seems to occur at about the same time in the evening or morning, it could be due to a surge created when the power company switches electrical grids to meet demand.

2.)  Check to see if the chirp (or chirping) occurs when something else in the house is turned on such as an exhaust or attic fan, a heater, etc.  If the smoke alarm is connected to a circuit with such a device, the alarm may chirp when the other device is switched on.  If this is the case and the device is plugged into a wall outlet, move it to another outlet on a different circuit.  If it is a hardwired device, have James Electric investigate it.

NOTE: These conditions can be minimized by installing your alarms on a dedicated circuit in compliance with NFPA requirements.

Replacing an Alarm

If none of these conditions exist and the suggestions don’t alleviate the symptom, the alarm should be replaced.  Age may be a factor in this case.  Smoke and heat alarms should be replaced every 10 years, and carbon monoxide and combination alarms should be replaced every 7 years.  Most of our alarms have a 5 year warranty from date of purchase (check your user manual).  A date code is stamped on the label attached to the back of the unit.

If the unit is out of warranty, purchase a replacement product.
If the unit is within warranty, please call Product Support at 1-800-880-6788.

NOTE: For more information about your specific alarm, refer to your user’s manual.

Download your Detector User guides here